| Warning:
Be sure to remove the three 1/4"-20 socket head capscrews after
installing the pressure plate. These keep the pressure plate from
binding when removing the cover from the flywheel. They will also
be necessary for disassembling the cover assembly. |
|
|
| Specifications |
|
|
|
| Base
Pressure & static adjustment (counterclockwise to increase) |
| 420
lbs (yellow spring) 15
lbs/turn |
|
| 690
lbs (black spring) 20
lbs/turn |
|
| 950
lbs (red spring) 30
lbs/turn |
|
| Torque
Specifications: 75 ft/lbs stand bolts, 85-100 ft/lbs 7/16 flywheel bolts |
|
100-125 ft/lbs. 1/2" Flywheel bolts |
| Ring
height - S104 lever - .350" (bottom of cover to top of pressure
ring) |
|
1.165" (top of cover to pressure ring) |
| Ring
height - LS10P5 lever - .200" (bottom of cover to top of pressure
ring) |
|
1.015" (top of cover to pressure ring) |
| Lever
weights - S104 - 5/16 55G, 1/4 45G, 3/16 35G |
| Lever
weights - LS10P5 - 5/16 72G, 1/4 52G |
|
| Lever
height - .030" below top of cover measured w/ straightedge |
|
|
| Note:
Check the flywheel bolt shoulder and overall length to make sure the
bolts do not bottom out on the shoulder or hit the back of the engine
block. Use either red or blue loctite on the flywheel bolts.
Re-torque the flywheel bolts after the first run and each time the
pressure plate is removed for servicing the unit. NEVER USE STAR
WASHERS ON AN ALUMINUM FLYWHEEL. |
|
|
| Counterweight
Adjustment |
|
| Mallory
Weight |
10.1g |
| Steel
Bolt 1/4"-20 x 1 1/4" |
9.3g |
| Steel
Bolt 1/4"-20 x 1 |
7.6g |
| Steel
Bolt 1/4"-20 x 3/4 |
6.4g |
| Aluminum
Bolt 1/4"-20 x 3/4 |
2.2g |
| Steel
Nut |
3.3g |
| Aluminum
Nut |
1.1g |
| Steel
Washer |
1.0g |
|
|
| Lever
Pressure Applied (1 gram per lever) |
|
| 5000
51lbs. |
|
| 6500
85lbs. |
|
| 7400
111lbs. |
|
|
|
| Repair
parts |
part number |
|
|
| lever,
S104 (2 hole cw) (6)* |
|
| lever,
LS10P5 (1 hole cw) 1/4" (6) |
|
| lever,
LS10P5 (1 hole cw) 5/16" (6) |
|
| Pin,
lever Pivot 5/16 x 1 1/4
(6) |
|
| Pin,
Yoke to Plate, 1/4 x 1 1/4 (6) |
|
| Pin,
lever to Yoke, 1/4 x 5/8 (6) |
|
| Capscrew,lever
Pivot, 5/16 x 18 x 3/4 (12) |
|
| Capscrew,Yoke
Pivot, 1/4 x 20 x 1/2 (12) |
|
| Yoke
(6) |
|
| Set
screw, lever ht. Adjuster (12) |
|
| Pressure
ring, (w/o insert ) |
|
| Pressure
ring Assembly, (w/Insert ) |
|
| Pressure
ring retaining bolt (3), 1/4x20x1 1/4 |
|
| replacement
cover |
|
| replacement
plate insert w/screws |
|
| replacement
flywheel insert w/screws |
|
| 2
disc drive stand stud (6) |
|
| 3
disc drive stand stud (6) |
|
| 3
disc stand spacer (6) |
|
| Cover
nut (6) |
|
| adjustable
stand (6) |
|
| pressure
adjuster w/ screw (6) |
|
| Spring
cup |
|
|
|
| Disc
5191 1 3/16-18 |
1378 |
| Disc
5191 1 3/8-10 |
1371 |
| Disc
5135 1 3/16-18 |
1388 |
| Disc
5135 1 3/8-10 |
1381 |
| Floater
plate steel |
3525 |
| Floater
plate bronze |
4525 |
|
|
| Gram
scale |
578 |
| Two
step switch |
580 |
| Dial
height gauge |
573 |
| Stand
strap |
583 |
| CW
set |
570 |
| CW
washer set 1-30g |
571 |
| Flywheel
bolt set 7/16 x 1 |
575 |
| Flywheel
bolt set 1/2 x 1 |
596 |
| Pilot
bushing for Chrysler in FW |
576 |
|
|
| GM
168T Flywheel |
|
| Ford
BB 168t Flywheel |
|
| Chrysler
8 Bolt 168t Flywheel |
|